logo
banner banner

News Details

Home > News >

Company news about IE4 Super Premium Efficiency Motor Launch: One 37kW Motor Saves About 1300 kWh of Electricity Per Year

Events
Contact Us
Mrs. Anny Song
86--18802094629
Contact Now

IE4 Super Premium Efficiency Motor Launch: One 37kW Motor Saves About 1300 kWh of Electricity Per Year

2026-11-13

China - BIMO has released its new IE4 super premium efficiency three phase asynchronous motor series, covering 0.75 kW to 315 kW with cast iron frames, 100 percent copper windings and IP55 protection. The first models to be available from stock are the 37 kW 6 pole versions YE4-225M-6 with B3 foot mounting and YE4-225M-6-B5 with B5 flange mounting.

What IE4 Means for a Buyer

IE4 is the highest efficiency class defined by IEC 60034-30-1, one step above IE3 premium efficiency. The difference is measured at full load: for a 37 kW 6 pole motor, IE3 requires an efficiency of about 94.1 percent, while IE4 reaches about 94.9 percent. That looks small on paper, but efficiency is a multiplier on every hour the motor runs, so a one point gain converts into a steady reduction in electricity bills for the whole service life of the machine.

One Motor, One Year: the Numbers

The calculation below uses a 37 kW motor running 4,000 hours per year at 100 percent load, which is typical for fans, pumps and cooling tower drives in two shift operation. Output energy is therefore 148,000 kWh per year, and input energy depends only on efficiency.

Efficiency Class Full Load Efficiency Annual Input Energy Annual Saving vs IE4
IE2 92.7 % 159,650 kWh about 3,700 kWh
IE3 94.1 % 157,280 kWh about 1,300 kWh
IE4 94.9 % 155,950 kWh reference

In plain language: replacing an IE3 37 kW motor with the new IE4 model saves roughly 1,300 kWh of electricity per motor per year, and moving up from an older IE2 unit saves about 3,700 kWh. At an industrial tariff of USD 0.15 per kWh, that is around USD 195 per year against IE3 and around USD 555 per year against IE2, for a single motor. A plant with twenty such drives is looking at a five figure annual difference, before any energy efficiency subsidy or carbon reporting benefit is counted.

Built for Continuous Duty

  • 100 percent copper winding with Class F insulation, so the extra efficiency is not achieved by using less material but by lower losses in a properly dimensioned winding.
  • Cast iron 225M frame and end shields for rigid support, low vibration and long bearing life in heavy duty service.
  • IP55 protection and IC411 cooling, suitable for humid pump rooms, dusty workshops and outdoor installations under a canopy.
  • 6 pole design at 1180 rpm on 415 V 60 Hz, with higher starting torque and lower speed for fans, mixers, crushers and screw conveyors.
  • B3 foot and B5 flange versions, so the same motor platform fits both floor mounted and close coupled installations.
  • CE marked and ISO 9001 certified production, every unit load tested with a test report supplied.

Where the Payback Comes Fastest

IE4 pays back quickest on motors that run many hours at high load. Typical cases are cooling tower fans in HVAC plants, circulation pumps in water treatment, ventilation fans in tunnels and car parks, and process fans in cement and chemical lines. On a 4,000 hour year, the extra purchase cost of the IE4 version is usually recovered within one to two years of operation, and the motor keeps saving for the next decade.

Availability

Series and range YE4, 0.75 kW to 315 kW, 2, 4, 6 and 8 pole
Stock models YE4-225M-6 (B3) and YE4-225M-6-B5 (B5 flange), 37 kW
Voltage and frequency 415 V 60 Hz standard, 380 V 50 Hz and 440 V 60 Hz on request
Minimum order 1 piece for trial order
Lead time 10 working days for stock, 25 to 35 days for production
Customization Winding for special voltage, shaft and flange to drawing, nameplate and packing for OEM

About BIMO

BIMO Machinery has manufactured electric motors since 2005, with two production bases in Zhejiang and Shanghai and exports to more than 50 countries. Between 80 and 90 percent of output is sold to overseas OEMs, distributors and project contractors in Europe, North America, the Middle East and Southeast Asia.

Want to know the exact saving for your application? Send us the motor power, running hours per year and your electricity tariff, and our engineer will return an energy saving calculation and a quotation within 12 hours.

Whatsapp:0086-18802094629  Emai:motorexport@bimo-idea.com

banner
News Details
Home > News >

Company news about-IE4 Super Premium Efficiency Motor Launch: One 37kW Motor Saves About 1300 kWh of Electricity Per Year

IE4 Super Premium Efficiency Motor Launch: One 37kW Motor Saves About 1300 kWh of Electricity Per Year

2026-11-13

China - BIMO has released its new IE4 super premium efficiency three phase asynchronous motor series, covering 0.75 kW to 315 kW with cast iron frames, 100 percent copper windings and IP55 protection. The first models to be available from stock are the 37 kW 6 pole versions YE4-225M-6 with B3 foot mounting and YE4-225M-6-B5 with B5 flange mounting.

What IE4 Means for a Buyer

IE4 is the highest efficiency class defined by IEC 60034-30-1, one step above IE3 premium efficiency. The difference is measured at full load: for a 37 kW 6 pole motor, IE3 requires an efficiency of about 94.1 percent, while IE4 reaches about 94.9 percent. That looks small on paper, but efficiency is a multiplier on every hour the motor runs, so a one point gain converts into a steady reduction in electricity bills for the whole service life of the machine.

One Motor, One Year: the Numbers

The calculation below uses a 37 kW motor running 4,000 hours per year at 100 percent load, which is typical for fans, pumps and cooling tower drives in two shift operation. Output energy is therefore 148,000 kWh per year, and input energy depends only on efficiency.

Efficiency Class Full Load Efficiency Annual Input Energy Annual Saving vs IE4
IE2 92.7 % 159,650 kWh about 3,700 kWh
IE3 94.1 % 157,280 kWh about 1,300 kWh
IE4 94.9 % 155,950 kWh reference

In plain language: replacing an IE3 37 kW motor with the new IE4 model saves roughly 1,300 kWh of electricity per motor per year, and moving up from an older IE2 unit saves about 3,700 kWh. At an industrial tariff of USD 0.15 per kWh, that is around USD 195 per year against IE3 and around USD 555 per year against IE2, for a single motor. A plant with twenty such drives is looking at a five figure annual difference, before any energy efficiency subsidy or carbon reporting benefit is counted.

Built for Continuous Duty

  • 100 percent copper winding with Class F insulation, so the extra efficiency is not achieved by using less material but by lower losses in a properly dimensioned winding.
  • Cast iron 225M frame and end shields for rigid support, low vibration and long bearing life in heavy duty service.
  • IP55 protection and IC411 cooling, suitable for humid pump rooms, dusty workshops and outdoor installations under a canopy.
  • 6 pole design at 1180 rpm on 415 V 60 Hz, with higher starting torque and lower speed for fans, mixers, crushers and screw conveyors.
  • B3 foot and B5 flange versions, so the same motor platform fits both floor mounted and close coupled installations.
  • CE marked and ISO 9001 certified production, every unit load tested with a test report supplied.

Where the Payback Comes Fastest

IE4 pays back quickest on motors that run many hours at high load. Typical cases are cooling tower fans in HVAC plants, circulation pumps in water treatment, ventilation fans in tunnels and car parks, and process fans in cement and chemical lines. On a 4,000 hour year, the extra purchase cost of the IE4 version is usually recovered within one to two years of operation, and the motor keeps saving for the next decade.

Availability

Series and range YE4, 0.75 kW to 315 kW, 2, 4, 6 and 8 pole
Stock models YE4-225M-6 (B3) and YE4-225M-6-B5 (B5 flange), 37 kW
Voltage and frequency 415 V 60 Hz standard, 380 V 50 Hz and 440 V 60 Hz on request
Minimum order 1 piece for trial order
Lead time 10 working days for stock, 25 to 35 days for production
Customization Winding for special voltage, shaft and flange to drawing, nameplate and packing for OEM

About BIMO

BIMO Machinery has manufactured electric motors since 2005, with two production bases in Zhejiang and Shanghai and exports to more than 50 countries. Between 80 and 90 percent of output is sold to overseas OEMs, distributors and project contractors in Europe, North America, the Middle East and Southeast Asia.

Want to know the exact saving for your application? Send us the motor power, running hours per year and your electricity tariff, and our engineer will return an energy saving calculation and a quotation within 12 hours.

Whatsapp:0086-18802094629  Emai:motorexport@bimo-idea.com