logo
banner banner

News Details

Home > News >

Company news about All Copper Winding Craft Cuts Motor Burnout and Oil Leakage, Lowering Maintenance Frequency on Site

Events
Contact Us
Mrs. Anny Song
86--18802094629
Contact Now

All Copper Winding Craft Cuts Motor Burnout and Oil Leakage, Lowering Maintenance Frequency on Site

2026-11-13

China - BIMO  Machinery has standardized 100 percent copper winding across its three phase asynchronous motor range, together with a revised sealing and bearing assembly on the end shields. The change targets the three complaints buyers raise most often in after sales service: winding burnout, oil and grease leakage, and the cost of frequent maintenance stops.

Why Copper Winding Reduces Burnout

A motor burns out when the insulation on the winding fails, and insulation fails faster as temperature rises. Copper has a conductivity of about 58 MS per metre, while aluminium is around 35 MS per metre, roughly 60 percent of copper. To carry the same current, an aluminium winding needs a larger cross section and still produces more resistive loss, which means a higher temperature rise inside the slot and at the winding ends.

The practical consequence is well documented in IEC thermal endurance terms: every 10 degrees Celsius of extra temperature rise halves the expected life of Class F insulation. A copper winding that runs 10 to 15 K cooler than an equivalent aluminium winding therefore keeps its insulation healthy for years longer, which is exactly where burnout starts - at the hottest point of the end winding, not at the terminal box.

Item Aluminium Winding Motor Copper Winding Motor
Conductivity about 35 MS per metre about 58 MS per metre
Winding temperature rise 10 to 15 K higher reference level
Typical winding life 3 to 5 years 8 to 10 years
Rewind or revarnish interval every 2 to 3 years every 6 to 10 years
Joint and terminal reliability sensitive to oxidation and creep stable under thermal cycling

Craft Details Behind the Number

  • 100 percent copper magnet wire, Class F or Class H enamel, with slot liner and phase insulation sized for the rated temperature rise.
  • Double dip and bake, plus vacuum pressure impregnation on request, so the winding becomes a solid block that resists vibration and moisture ingress.
  • Formed and tied end windings, with phase separators and lacing thread, preventing the rubbing that shortens insulation life.
  • High potential test and insulation resistance test on every stator before assembly, plus a full load run test at the end of the line.
  • Class F insulation with Class B temperature rise in normal duty, leaving a thermal margin for voltage fluctuation and short overloads.

Where the Oil and Grease Leakage Comes From

Leakage on a motor rarely comes from the winding. It usually comes from the bearing chamber, and it is a design and machining issue rather than a wear issue. BIMO addresses it on four points:

  • Machined sealing faces on the end shield and frame, held to a flatness tolerance and sealed with oil resistant gasket, so grease cannot creep along the joint.
  • Double lip oil seals or sealed for life bearings, selected according to mounting position, with the lip facing the correct side for the shaft rotation.
  • Grease relief and drain arranged so that over greasing during maintenance does not push grease into the winding or onto the floor.
  • IP55 assembly test with gaskets on the terminal box and shaft seal, verified on the line before packing.

What This Means for Maintenance Planning

Winding inspection Insulation resistance check once a year, no rewind expected for 8 to 10 years in normal duty.
Bearing service Grease replenishment at 6,000 to 8,000 running hours for sealed bearing versions, longer with sealed for life bearings.
Seal and gasket check Visual check at each planned shutdown, replacement only when the lip seal shows hardening.
Unplanned stops Copper winding units typically report one day or less per year on fans and pumps, against three to five days for aluminium wound units in the same duty.

For a plant running dozens of small and medium motors, the difference is not only the rewind cost. It is the production time lost when a fan stops in summer, the labour cost of pulling a motor out of a pump skid, and the risk that a burnt winding damages the driven equipment. Lower maintenance frequency is the outcome buyers actually pay for.

Availability

Copper winding is standard on the MS series aluminium housing motors from 0.37 kW to 7.5 kW, on the YE3 and YE4 cast iron series up to 315 kW, and on explosion proof and high voltage ranges. Test reports, winding data and material certificates are supplied with each order, and OEM nameplate and packing are available.

Want to compare the maintenance cost of copper and aluminium winding for your fleet? Send us your motor list and duty cycle, and our engineer will reply with a winding specification and quotation within 12 hours.

Whatsapp:0086-18802094629  Emai:motorexport@bimo-idea.com

banner
News Details
Home > News >

Company news about-All Copper Winding Craft Cuts Motor Burnout and Oil Leakage, Lowering Maintenance Frequency on Site

All Copper Winding Craft Cuts Motor Burnout and Oil Leakage, Lowering Maintenance Frequency on Site

2026-11-13

China - BIMO  Machinery has standardized 100 percent copper winding across its three phase asynchronous motor range, together with a revised sealing and bearing assembly on the end shields. The change targets the three complaints buyers raise most often in after sales service: winding burnout, oil and grease leakage, and the cost of frequent maintenance stops.

Why Copper Winding Reduces Burnout

A motor burns out when the insulation on the winding fails, and insulation fails faster as temperature rises. Copper has a conductivity of about 58 MS per metre, while aluminium is around 35 MS per metre, roughly 60 percent of copper. To carry the same current, an aluminium winding needs a larger cross section and still produces more resistive loss, which means a higher temperature rise inside the slot and at the winding ends.

The practical consequence is well documented in IEC thermal endurance terms: every 10 degrees Celsius of extra temperature rise halves the expected life of Class F insulation. A copper winding that runs 10 to 15 K cooler than an equivalent aluminium winding therefore keeps its insulation healthy for years longer, which is exactly where burnout starts - at the hottest point of the end winding, not at the terminal box.

Item Aluminium Winding Motor Copper Winding Motor
Conductivity about 35 MS per metre about 58 MS per metre
Winding temperature rise 10 to 15 K higher reference level
Typical winding life 3 to 5 years 8 to 10 years
Rewind or revarnish interval every 2 to 3 years every 6 to 10 years
Joint and terminal reliability sensitive to oxidation and creep stable under thermal cycling

Craft Details Behind the Number

  • 100 percent copper magnet wire, Class F or Class H enamel, with slot liner and phase insulation sized for the rated temperature rise.
  • Double dip and bake, plus vacuum pressure impregnation on request, so the winding becomes a solid block that resists vibration and moisture ingress.
  • Formed and tied end windings, with phase separators and lacing thread, preventing the rubbing that shortens insulation life.
  • High potential test and insulation resistance test on every stator before assembly, plus a full load run test at the end of the line.
  • Class F insulation with Class B temperature rise in normal duty, leaving a thermal margin for voltage fluctuation and short overloads.

Where the Oil and Grease Leakage Comes From

Leakage on a motor rarely comes from the winding. It usually comes from the bearing chamber, and it is a design and machining issue rather than a wear issue. BIMO addresses it on four points:

  • Machined sealing faces on the end shield and frame, held to a flatness tolerance and sealed with oil resistant gasket, so grease cannot creep along the joint.
  • Double lip oil seals or sealed for life bearings, selected according to mounting position, with the lip facing the correct side for the shaft rotation.
  • Grease relief and drain arranged so that over greasing during maintenance does not push grease into the winding or onto the floor.
  • IP55 assembly test with gaskets on the terminal box and shaft seal, verified on the line before packing.

What This Means for Maintenance Planning

Winding inspection Insulation resistance check once a year, no rewind expected for 8 to 10 years in normal duty.
Bearing service Grease replenishment at 6,000 to 8,000 running hours for sealed bearing versions, longer with sealed for life bearings.
Seal and gasket check Visual check at each planned shutdown, replacement only when the lip seal shows hardening.
Unplanned stops Copper winding units typically report one day or less per year on fans and pumps, against three to five days for aluminium wound units in the same duty.

For a plant running dozens of small and medium motors, the difference is not only the rewind cost. It is the production time lost when a fan stops in summer, the labour cost of pulling a motor out of a pump skid, and the risk that a burnt winding damages the driven equipment. Lower maintenance frequency is the outcome buyers actually pay for.

Availability

Copper winding is standard on the MS series aluminium housing motors from 0.37 kW to 7.5 kW, on the YE3 and YE4 cast iron series up to 315 kW, and on explosion proof and high voltage ranges. Test reports, winding data and material certificates are supplied with each order, and OEM nameplate and packing are available.

Want to compare the maintenance cost of copper and aluminium winding for your fleet? Send us your motor list and duty cycle, and our engineer will reply with a winding specification and quotation within 12 hours.

Whatsapp:0086-18802094629  Emai:motorexport@bimo-idea.com